Remote monitoring of weld purge up to 1 km away
PUBLISHED: 31 Aug 17
PurgEye® 1000 Weld Purge Monitor® in use
When welding lengths of tube and pipework fabrications, as well as sections of pipelines of 20 metres length and more, one problem operators face is not receiving a fast and true weld purge reading from the purge zone.
Now, for the first time, Huntingdon Fusion Techniques HFT® makes it possible to have an immediate reading of the weld purge gas at the underside of the joint, from any distance up to 1,000 metres away with their PurgEye® 1000 Weld Purge Monitor®.
Luke Keane, Distributor Support for HFT® said: "By using a remote sensing head, which can be fitted onto any Mechanical or Inflatable Tube and Pipe Weld Purging System from 1" (25 mm) diameter upwards, the oxygen level can be measured directly at the weld location and the information will be electronically transferred to the monitor up to 1 km away. With this capability, the operator can be certain that the weld purge reading is correct and that the joint will not be adversely affected by oxidation."
"The PurgEye® 1000 is one of our five Weld Purge Monitors® to now feature PurgeNet™, a networking device designed for communicating the current oxygen reading from the Monitor, to another piece of equipment, such as the visual warning accessory PurgeAlarm™ or a Dew Point Monitor with additional inter-pass temperature monitoring."
If exhaust gas from a normal weld purge system is piped down a hose to a distant measuring instrument, it may take many minutes, or even hours in some cases, for a stable reading to reach the sensor. The exhaust gas may even be contaminated on the way by outgassing from the walls of the hose material or from air drawn in through a leaky connection.
In the event the oxygen level is too high, the weld would become oxidised at best and might even have nitrogen and hydrogen absorbed into the joint at worst, which could cause metallurgical defects leading to other problems.
The PurgEye® 1000 Weld Purge Monitor® has been designed and developed specifically to prevent oxidation under distance monitoring conditions and has a sensor placed immediately next to the weld purge site.
The sensor is secured in a tiny module, which is mounted inside the purging system and is connected to the measuring instrument by a data cable. The purge reading is sent back to the instrument at the speed of light, so operators and quality control personnel know immediately when the purge is satisfactory.
This way, the operator can be certain that the weld purge reading is correct and that the joint will not be adversely affected by oxidation, allowing welders to achieve that sought after zero colour weld.
The PurgEye® 1000 measures oxygen levels from 1,000 parts per million (ppm), right down to 1 ppm (accurate to 10 ppm), ideal for welding metals such as stainless steels, duplex steels, titanium and zirconium where oxide free, zero colour welds are required time after time.
Safe, fast and low cost pipe freezing with Qwik-Freezer™
Glass fibre Backing Tape gives improved weld root profiles
Special high quality, leak tight welding hose for argon feed
Tight sealing Low Profile Pipestoppers for limited spaces and restricted access
Huntingdon Fusion Techniques HFT® to Exhibit at World Nuclear
Lightweight aluminium plugs for heavy-duty applications
Cut costs, not corners with QuickPurge®
Achieve high quality welds with a close eye on your weld purge
Versatile, lightweight nylon plugs for Weld Purging
Improve weld quality with a low cost Trailing Shield®
Versatile Inflatable Stoppers for pipe plugging and stopping
Improve weld quality with precision ground Tungsten Electrodes
HotPurge®, for weld purging heat-treated chrome and high strength stainless steel pipework
Inflatable Rubber Plugs: lightweight but strong and highly resistant to petrochemicals
Successful titanium welding with Flexible Welding Enclosures®