Weld Purge Dams for dished ends and short pipes

PUBLISHED: 31 Jan 18

The Weld Purge Dams are fitted with a dual inflation and purge hose, an additional purge gas hose and an exhaust which can be connected to one of the HFT® Weld Purge Monitors®
The Weld Purge Dams are fitted with a dual inflation and purge hose, an additional purge gas hose and an exhaust which can be connected to one of the HFT® Weld Purge Monitors®

Weld Purging (back purging) describes the removal of oxygen from the vicinity of a weld before, during and after welding. For pipe and tank welding of stainless steels, titanium and chrome steels, it is good practice to restrict the area required to be purged, usually with an inflatable tandem weld purging system.

For the purging of short pipe pieces and dished end or dome end welds however, the tandem devices are unsuitable. Welders and their helpers over the years have created single dams to block the ends, of pipes and cylindrical tanks using easily obtainable, locally available material.

Ron Sewell, Chairman at Huntingdon Fusion Techniques HFT® said: "Even today, many companies are still allowing their technicians to spend many hours fabricating dams made of foam, cardboard, adhesive tape, wood, paper and so on. These materials contain a high percentage of water, which is very undesirable to have in the presence of a weld."

"As these old fashioned, poor quality dams and materials are warmed by the welding operation, they start to outgas their water vapour, which starts to circulate around the weld joint and combine with the weld pool to cause porosity and oxidation, leading to metallurgical defects."

"In addition, the purging process takes many times longer to reach a low enough level for welding to begin at which point the inert gas flow needs to be raised to a much higher level to combat the outgassing."

Using the technology and skills that they have obtained over 43 years of design and manufacture, Huntingdon Fusion Techniques HFT® has created a series of low cost, but professionally manufactured Weld Purge Dams, using low vapour pressure materials that seal tightly around the circumference of the volume to be purged.

Available for pipe diameters from 6 to 88 inches (150 mm up to 2,235 mm), the HFT® Single Ended Inflatable Weld Purge Dams are made of low vapour pressure materials specially selected for optimum weld purging results to provide the lowest oxygen reading in the fastest possible time with the minimum use of expensive argon gas.

The Weld Purge Dams are fitted with a dual inflation and purge hose, an additional purge gas hose and an exhaust which can be connected to one of the HFT® Weld Purge Monitors®

The additional purge gas hose is suitable for introducing extra purge gas into the weld zone at any time to cool welds to meet interpass temperature specifications, or to provide more inert gas in the event of titanium, zirconium or special stainless applications needing a guaranteed zero colour weld.

Once the Dam is inflated using the purge gas and seals all around the internal circumference of the pipe, the excess inert purge gas spills out and purges the space around the weld joint. The air (oxygen) is then released out and into the open through a series of venting exhausts on the dam.

Four pull tags are located around the circumference of the Weld Purge Dam, so rope or pull wires can be attached for retrieval of the deflated system, as required. By producing bright shiny welds, there will be no porosity and there will be no loss of corrosion resistance caused by oxidation.

Apart from the benefit of having a metallurgically sound weld, the difficulties of cleaning an oxidised weld are eliminated, saving vast amounts of money in labour and material costs as well as the disposal costs where acids are concerned. Now there is no more reason to put welds at risk by using apparently cheaper materials, when for a very low cost, Argweld® Inflatable Weld Purge Dams can be purchased instead!

Huntingdon Fusion Techniques Limited, UK
Tel: + 44 1554 836 836
Email: marketing@huntingdonfusion.com
Web: www.huntingdonfusion.com

More news from this company:
Huntingdon Fusion Techniques HFT® to Exhibit at World Nuclear
Lightweight aluminium plugs for heavy-duty applications
Cut costs, not corners with QuickPurge®
Achieve high quality welds with a close eye on your weld purge
Versatile, lightweight nylon plugs for Weld Purging
Improve weld quality with a low cost Trailing Shield®
Versatile Inflatable Stoppers for pipe plugging and stopping
Improve weld quality with precision ground Tungsten Electrodes
HotPurge®, for weld purging heat-treated chrome and high strength stainless steel pipework
Inflatable Rubber Plugs: lightweight but strong and highly resistant to petrochemicals
Successful titanium welding with Flexible Welding Enclosures®
PurgElite® for zero colour tube and pipe welds
Accurate stainless and titanium weld purging with the PurgEye® 200
Low cost nylon Weld Purge Plugs™
No risk of lost welds with Weld Purge Film®